Body type: Straight-through S-type cast valve
Plug type: Balance cage single-seat plunger valve core
Nominal diameter: DN15~300mm; NPS 1/2″~12″
Nominal pressure: PN1.6~6.4MPa;Class 150~300LB
Applicable temperature: -196℃~550℃ (Optional according to working conditions)
Type of connection: Flange, welding, thread (applicable within 1″)
Flange distance: According to IEC 60534
Gland type: Bolt compression type
Sealing gasket: Metal graphite spiral wound gasket
Packing: PTFE, flexible graphite
Actuator: Pneumatic actuator, electric actuator
TangoValve Group produces a series of double-sealed sleeve control valve,for which sleeve-guided and pressure-balanced plugs are adopted. Top-guide sleeve control valve is a double-sealed sleeve structure, which is mainly used in occasions with low leakage requirements. Because both sealing surfaces of the double seal structure are metal seals, the temperature range for use is wider.
| Z | Actuator |
| Z Series Control Valve | J: Pneumatic diaphragm actuator H: Pneumatic piston actuator R: Electric 3810L actuator D: Electric PSL actuator |
| H | Structural Style |
| H Straight Stroke | M: Standard sleeve control valve MF: Soft seal sleeve control valve ML: Single-stage cage type control valve MG: Sleeve control valve with heat dissipation MV: Bellows type sleeve control valve |
Top-Guide Single-Seated Control Valve seat adopts pressure cage structure, which has the characteristics ofstrong reliability and convenient replacement and maintenance in the later stage.and solves the problem that the traditional structure without valve seat cannot bereplaced due to leakage. The service life can be extended. With fow opening design.the medium tends to the direction of valve opening, with good controllability ofsmall opening and small fow characteristic distortion. According to the workingconditions, electric or pneumatic actuators can be selected for control.
Carbon steel for body material*
| No. | Component | Material | ||
| 1 | Body | WCB | LCB | WC9 |
| 2 | Gasket | 316 + Graphite/FTFE | 316 + Graphite/FTFE | 316 + Graphite/FTFE |
| 3 | Seat | 304 | 304 | 304 |
| 4 | Plug | 304 | 304 | 304 |
| 5 | Copper bush | Cu/316L | Cu/316L | Cu/316L |
| 6 | Guide sleeve | 304 | 304 | 304 |
| 7 | Gasket | 316 + Graphite/FTFE | 316 + Graphite/FTFE | 316 + Graphite/FTFE |
| 8 | Bonnet | WCB | LCB | WC9 |
| 9 | Nut | 304 | 304 | 304 |
| 10 | Double-screw bolt | 304 | 304 | 304 |
| 11 | Stem | 304 | 304 | 304 |
| 12 | Packing | PTFE/Flexible graphite | PTFE/Flexible graphite | PTFE/Flexible graphite |
| 13 | Lock nut | 304 | 304 | 304 |
| 14 | Pressing sleeve | 304 | 304 | 304 |
| 15 | Plate | 304 | 304 | 304 |
Body Materialls Stainless Steel*
| No. | Component | Material | ||
| 1 | Body | CF8 | CF8M | CF3M |
| 2 | Gasket | 316 + Graphite/FTFE | 316 + Graphite/FTFE | 316 + Graphite/FTFE |
| 3 | Seat | 304 | 316 | 316L |
| 4 | Plug | 304 | 316 | 316L |
| 5 | Copper bush | Cu/316L | Cu/316L | Cu/316L |
| 6 | Guide sleeve | 304 | 316 | 316L |
| 7 | Gasket | 316 + Graphite/FTFE | 316 + Graphite/FTFE | 316 + Graphite/FTFE |
| 8 | Bonnet | CF8 | CF8M | CF3M |
| 9 | Nut | 304 | 316 | 316L |
| 10 | Double-screw bolt | 304 | 316 | 316L |
| 11 | Stem | 304 | 316 | 316L |
| 12 | Packing | PTFE/Flexible graphite | PTFE/Flexible graphite | PTFE/Flexible graphite |
| 13 | Lock nut | 304 | 316 | 316L |
| 14 | Pressing ring | 304 | 316 | 316L |
| 15 | Plate | 304 | 316 | 316L |
Note: 1. The above is of standard confguration structure; The valve seat is metal seal, and the valve seat is soft seal, grade Vl optional. lt canprovide valve trim of spray welding cemented carbide.2.The conventional materialis carbon steel and stainless stee., and the special materiaregulating valve products can be customized according to the user’s work conditions.
| Inside Diameter(mm/in) | 20 (3/4″) | 25 (1″) | 32 (1-1/4″) | 40 (1-1/2″) | 50 (2″) | 65 (2-1/2″) | 80 (3″) | 100 (4″) | 125 (5″) | 150 (6″) | 200 (8″) | 250 (10″) | 300 (12″) | |
| Flow Coefficient (KV) | Straight Line | 6.9 | 11 | 17.6 | 27.5 | 44 | 69 | 110 | 176 | 275 | 440 | 690 | 1100 | 1760 |
| Percent (%) | 6.3 | 10 | 16 | 25 | 40 | 63 | 100 | 160 | 250 | 400 | 630 | 1000 | 1600 | |
| Pneumatic Actuator | HA/B-22 | HA/B-23 | HA/B-34 | HA/B-45 | HA/B-56 | |||||||||
| Area | 350 cm² | 350 cm² | 560 cm² | 900 cm² | 900 cm² | |||||||||
| Mode of action | Spring Range | Metal seal allows differential pressure(MPa) | ||||||||||||
| Gas Opening | 20–100 KPa | 1.16 | 0.7 | 0.44 | 0.28 | 0.18 | 0.17 | 0.11 | 0.07 | 0.07 | 0.05 | 0.03 | 0.02 | 0.01 |
| 40–200 KPa | 3.34 | 2.14 | 1.31 | 0.84 | 0.53 | 0.51 | 0.33 | 0.21 | 0.21 | 0.15 | 0.09 | 0.06 | 0.04 | |
| 80–240 KPa | 6.4 | 4.99 | 3.05 | 1.95 | 1.25 | 1.18 | 0.78 | 0.5 | 0.5 | 0.36 | 0.21 | 0.15 | 0.08 | |
| Gas Off | 20–100 KPa | 2.23 | 2.14 | 0.87 | 0.56 | 0.36 | 0.34 | 0.22 | 0.14 | 0.14 | 0.1 | 0.06 | 0.03 | 0.02 |
| 40–200 KPa | 6.4 | 6.4 | 5.86 | 3.64 | 2.3 | 2.21 | 1.43 | 0.91 | 0.91 | 0.66 | 0.37 | 0.25 | 0.2 | |
| 80–240 KPa | 6.4 | 6.4 | 6.4 | 5.04 | 3.18 | 3.06 | 1.98 | 1.26 | 1.26 | 0.92 | 0.52 | 0.47 | 0.35 | |
| Electric Actuator | Metal seal allows differential pressure(MPa) | |||||||||||||
| Thrust(N) | 800 | 2.38 | ||||||||||||
| 2000 | 4.77 | 3.05 | 1.86 | 1.19 | 0.76 | |||||||||
| 3000 | 2.79 | 1.79 | 1.14 | |||||||||||
| 5000 | 4.66 | 2.98 | 1.91 | 1.13 | 0.6 | 0.47 | ||||||||
| 6500 | 1.35 | 0.8 | 0.57 | 0.39 | 0.26 | 0.16 | ||||||||
| 10000 | 0.61 | 0.42 | 0.2 | 0.15 | ||||||||||
| 16000 | 0.97 | 0.67 | 0.35 | 0.12 | 0.09 | |||||||||
| Model | Pneumatic film actuator | Electronic electric actuator |
| Form | ZH22~ZH56 | 3810L, RSL |
| Type | Multi spring | Intelligent integrated type |
| Purpose | Adjustment, switch | Regulating |
| Drive | Air pressure (spring range): 140 (20~100) KPa G 240 (40~200) KPa G 280 (80~240) KPa G | Power supply: AC 220 V ±10% 50Hz AC 380 V ±10% 50Hz |
| Joint | Rc 1/4 | Common type: 2–PF(G1/2”) Flameproof type: 2–PF(G3/4”) |
| Positive Action | Air pressure increases to push the valve to close | Control signal increases to push the valve to close |
| Reaction | Air pressure increases to push the valve open | Control signal increases to push the valve open |
| Control Signal | 4~20mA.DC (With positioner) | Input output 4~20mA.DC |
| Lag | ≤1% FS (With positioner) | ≤0.8% FS |
| Linearity | 2% FS (With positioner) | ≤±1% FS |
| Ambient Temperature | -10°C ~ +70°C | |
| Surface Coating | Black phosphating treatment Actuator: Acrylic polyurethane paint | |
| Optional Accessories | Optional accessories, Hand wheel, Magnetic valve, Travel switch, Lock up valve | Heater |
| Flow Characteristics | Equal percentage, Straight line | |
| Adjustable Range | 50:01:00 | |
| Rated Cv Value | Equal percentage: 10~1400 Straight line: 11~1500 | |
| Allowable Leakage | Hard seal: Level-IV (0.01% rated flow of valve) Soft seal: Level-V | |
| Drive Mode | Pneumatic | Electric |
| Intrinsic Error (%) | ±1.0 | ±1.0 |
| Return Difference (%) | ≤1.0 | ≤1.0 |
| Dead Zone (%) | ≤0.6 | ≤1.0 |
| Constant Point Deviation (%) | ±2.5 | ±2.5 |
| Rated Stroke Deviation (%) | ≤2.5 | ≤2.5 |
| DN (In) | 20 (3/4″) | 25 (1″) | 32 (1-1/4″) | 40 (1-1/2″) | 50 (2″) | 65 (2-1/2″) | 80 (3″) | 100 (4″) | 125 (5″) | 150 (6″) | 200 (8″) | 250 (10″) | 300 (12″) |
| L | |||||||||||||
| PN16/25 | 181 | 184 | 200 | 222 | 254 | 276 | 298 | 352 | 410 | 451 | 600 | 650 | 700 |
| PN40 | 181 | 184 | 200 | 222 | 254 | 276 | 298 | 352 | 410 | 451 | 600 | 670 | 770 |
| PN64 | 210 | 210 | 210 | 251 | 286 | 311 | 337 | 394 | 440 | 508 | 650 | 690 | 800 |
| H | |||||||||||||
| PN16/25 | 52.5 | 57.5 | 75 | 75 | 85.5 | 92.5 | 100 | 110 | 142.5 | 158 | 170 | 195 | 230 |
| PN40 | 52.5 | 57.5 | 75 | 75 | 82.5 | 92.5 | 100 | 117.5 | 150 | 167.5 | 187.5 | 205 | 245 |
| PN64 | 65 | 40 | 85 | 85 | 90 | 102.5 | 107.5 | 125 | 172.5 | 195 | 207.5 | 230 | 260 |
| H1 | 132 | 132 | 158 | 170 | 179 | 214 | 221 | 234 | 270 | 294 | 331 | 390 | 450 |
| H2 | 285 | 285 | 285 | 285 | 285 | 360 | 360 | 360 | 470 | 470 | 470 | 580 | 580 |
| H3 | 208 | 208 | 224 | 228 | 228 | 334 | 334 | 342 | 408 | 453 | 482 | 520 | 550 |
| H4 | 153 | 153 | 153 | 153 | 153 | 181 | 181 | 181 | 247 | 247 | 247 | / | / |
| H5 | 336 | 338 | 402 | 405 | 405 | 627 | 628 | 635 | 698 | 702 | 728 | 755 | 790 |
| H6 | 700( According to the actualtemperature) | ||||||||||||
| H7 | 88 | 88 | 88 | 88 | 88 | 95 | 95 | 95 | 110 | 110 | 140 | 140 | 140 |
| D | 310 | 310 | 355 | 390 | 430 | 465 | 520 | 585 | 660 | 770 | 890 | 950 | |
| A | 200 | 200 | 200 | 200 | 200 | 240 | 240 | 240 | 350 | 350 | 350 | 450 | 450 |
| C | 282 | 282 | 282 | 282 | 282 | 360 | 360 | 360 | 470 | 470 | 470 | 650 | 650 |
| Flange | Executable: GB、HG、JB、DIN、JIS、ANSl Corresponding standard | ||||||||||||
| DN (In) | 20 (3/4″) | 25 (1″) | 32 (1-1/4″) | 40 (1-1/2″) | 50 (2″) | 65 (2-1/2″) | 80 (3″) | 100 (4″) | 125 (5″) | 150 (6″) | 200 (8″) | 250 (10″) | 300 (12″) |
| L | |||||||||||||
| PN16/25 | 181 | 184 | 200 | 222 | 254 | 276 | 298 | 352 | 410 | 451 | 600 | 640 | 880 |
| PN40 | 181 | 184 | 200 | 222 | 254 | 276 | 298 | 352 | 410 | 451 | 600 | 640 | 880 |
| PN64 | 210 | 210 | 210 | 251 | 286 | 311 | 337 | 394 | 440 | 508 | 650 | 810 | 950 |
| H | |||||||||||||
| PN16/25 | 52.5 | 57.5 | 75 | 75 | 85.5 | 92.5 | 100 | 110 | 142.5 | 158 | 170 | 195 | 230 |
| PN40 | 52.5 | 57.5 | 75 | 75 | 82.5 | 92.5 | 100 | 117.5 | 150 | 167.5 | 187.5 | 205 | 245 |
| PN64 | 65 | 40 | 85 | 85 | 90 | 102.5 | 107.5 | 125 | 172.5 | 195 | 207.5 | 230 | 260 |
| H1 | 132 | 132 | 158 | 170 | 179 | 214 | 221 | 234 | 270 | 294 | 331 | 390 | 450 |
| H2 | 373 | 373 | 456 | 456 | 538 | 538 | 548 | 548 | 725 | 725 | 725 | 795 | 795 |
| H3 | 208 | 208 | 224 | 228 | 228 | 334 | 334 | 342 | 408 | 453 | 482 | 520 | 550 |
| H4 | 90 | 90 | 90 | 90 | 90 | 90 | 90 | 90 | 90 | 90 | 90 | 90 | 90 |
| H5 | 336 | 338 | 402 | 405 | 405 | 627 | 628 | 635 | 698 | 702 | 728 | 755 | 790 |
| H6 | 700( According to the actualtemperature) | ||||||||||||
| H7 | 88 | 88 | 88 | 88 | 88 | 95 | 95 | 95 | 95 | 110 | 110 | 140 | 140 |
| D | 310 | 310 | 355 | 355 | 390 | 430 | 465 | 520 | 585 | 660 | 770 | 890 | 950 |
| A | 225 | 225 | 225 | 225 | 255 | 255 | 255 | 255 | 255 | 310 | 310 | 350 | 350 |
| Flange | Executable: GB、HG、JB、DIN、JIS、ANSl Corresponding standard | ||||||||||||
Note: 1. The dimensions in the table are standard data without accessories. The dimensions of accessories are calculated according to the actualconhquration.2. Due to the technical innovation and improvement of the product, the size may change. Please contact the technical departmentof the Company for the latest information.
Chemical Processing: Regulates the flow of chemicals in reactors and pipelines.
Oil and Gas: Controls the movement of hydrocarbons in refining and distribution.
Water Treatment: Manages water flow in purification and distribution systems.
Power Generation: Adjusts steam flow in boilers and turbines.
Pharmaceuticals: Ensures precise dosing and mixing of ingredients.
اكتشف حلول الصمامات المتميزة لدينا وعزز كفاءتك.
الاتصال
نحن الآن لمعرفة كيف يمكننا دعم احتياجاتك بجودة عالية
المنتجات والخدمة الاستثنائية.
0577—86938599
© تانغ غونغ صمام المجموعة.
جميع الحقوق محفوظة.
